Skip to main content

Posts

Showing posts with the label Automatic

Automatic Night Lamp with Morning Alarm Circuit Diagram

This circuit automatically turns on a night lamp when bedroom light is switched off. The lamp remains ‘on’ until the light sensor senses daylight in the morning. A super-bright white LED is used as the night lamp. It gives bright and cool light in the room. When the sensor detects the daylight in the morning, a melodious morning alarm sounds. The circuit is powered from a standard 0-9V transformer. Diodes D1 through D4 rectify the AC voltage and the resulting DC voltage is smoothed by C1. Regulator IC 7806 gives regulated 6V DC to the circuit. A battery backup is provided to power the circuit when mains fails. When mains supply is available, the 9V rechargeable battery charges via diode D5 and resistor R1 with a reasonably constant current. In the event of mains failure, the battery automatically takes up the load without any delay. Diode D5 prevents the battery from discharging backwards following the mains failure and diode D6 provides current path from the battery.  Automatic Ni...

Automatic Night Light Feeds Directly From the AC Line

There are many approaches to the problem of activating a light when it becomes dark, and a recent Design Idea covers this topic (Reference 1). Some approaches require a dc power supply and an electromechanical relay, but a better approach involves feeding the device directly from the ac line, minimizing the number of components  ( Figure 1 ). Figure 1. The photoresistor activates the TRIAC and the load when darkness falls. The heart of the device is a light-sensitive cadmium-sulphide resistor, PR, with a resistance of approximately 200 kΩ in the dark and decreasing to a few kilohms in the light. PR and capacitor C1 form an ac-voltage divider. In daylight, the voltage across PR is too low to generate the required gate-trigger current to turn on bidirectional ac switch Q1, thus keeping the load – usually a lamp – off. When it becomes dark, PR’s resistance rises, resulting in an increase in the TRIAC’s gate current that triggers the TRIAC and lights the lamp. The circuit uses inexpens...

Automatic Curtain Opener Circuit Project

Automatic Curtain Opener Circuit Diagram . This circuit can be used with a timer clock to open and close curtains or (vertical) Venetian blinds. The curtain or blind is driven by  an electric motor with a reduction gearbox fitted to the control mechanism of the curtain or blind. This circuit is ideal for giving your home an occupied appearance while you are away on holiday or for some other reason. In the author’s house, this arrangement has provided several years of trouble-free service on a number of windows fitted  with Venetian blinds.  The original design was a simple relay circuit with pushbuttons for opening and closing and reed switches acting as limit switches. The mechanical drive is provided by a small DC motor with a reduction gearbox and pulley (all from Conrad Electronics).  It was later modified to work automatically with a timer clock. The timer operates a small  230-VAC (or 120-VAC) relay with a changeover contact. Thanks to the two timers, the ...

Automatic Automotive Burglar Alarm

Alarm triggers on after a 13 second delay and stays on for 1-1 Vfe minutes. Then it resets automatically It can also be turned off and reset by opening and reclosing SI. Automotive Burglar Alarm Circuit Diagram

Automatic Plant Irrigator

Automatic Plant Irrigator Circuit Diagram . The circuit presented here waters your plants regularly when you are out for a vacation. The circuit comprises a sensor part built using only one op-amp (N1) of quad op-amp IC LM324. Op-amp N1 is configured here as a comparator. Two stiff cop-per wires are inserted in the soil containing plants. As long as the soil is wet, conductivity is maintained and the circuit remains off. When the soil dries out, the resistance between the copper wires (sensor probes A and B) increases. If the resistance increases beyond a preset limit, output pin 1 of op-amp N1 goes ‘low’.  Automatic Plant Irrigator Circuit Diagram This triggers timer IC2 (NE 555) configured as a monostable multivibrator. As a result, relay RL1 is activated for a preset time. The water pump starts immediately to supply water to the plants. As soon as the soil becomes sufficiently wet, the resistance between sensor probes decreases rapidly. This causes pin 1 of op-amp N1 to go ‘hig...

Simple Automatic Water Pump Controller Circuit Diagram

Simple Automatic Water Pump Controller Circuit Diagram is a series of functions to control the Automatic Water Pump Controller Circuit in a reservoir or water storage. As the water level sensor made with a metal plate mounted on the reservoir or water tank, with a sensor in the short to create the top level and a detection sensor for detecting long again made the lower level and ground lines connected to the bottom of reservoirs or reservoir.  The series of automatic water pump controller is designed with 2 inputs NOR by 4 pieces and relay that is activated by the transistor. Automatic water pump circuit requires +12 VDC voltage source and can be used to control the water pump is connected to AC power . Here is the complete series of pictures. Automatic Water Pump Controller Circuit Diagram working principle series of automatic water pump controller above is. At the time the water level is below both sensors, the output IC1C (pin 10) will be LOW, Kemudin when the water began to to...

Automatic Loudness Control

Circuit diagram: Parts P1 10K Linear Potentiometer (Dual-gang for stereo) R1,R6,R8 100K 1/4W Resistors R2 27K 1/4W Resistor R3,R5 1K 1/4W Resistors R4 1M 1/4W Resistor R7 20K 1/2W Trimmer Cermet C1 100nF 63V Polyester Capacitor C2 47nF 63V Polyester Capacitor C3 470nF 63V Polyester Capacitor C4 15nF 63V Polyester Capacitor C5,C9 1µF 63V Electrolytic or Polyester Capacitors C6,C8 47µF 63V Electrolytic Capacitors C7 100pF 63V Ceramic Capacitor IC1 TL072 Dual BIFET Op-Amp SW1 DPDT Switch (four poles for stereo) Comments:   In order to obtain a good audio reproduction at different listening levels, a different tone-controls setting should be necessary to suit the well known behaviour of the human ear. In fact, the human ear sensitivity varies in a non-linear manner through the entire audible frequency band, as shown by Fletcher-Munson curves. A simple approach to this problem can be done inserting a circuit in the preamplifier stage, capable of varying automatically the frequency respo...

Traction Battery and Automatic Battery Charger

9V Automatic Battery NiCd Charger

This automatic NiCd charger for 9V NiCd batteries is using 555 timer properties and is very easy to build. Why is an automatic 9 volts NiCd battery charger? Because you can leave the battery for charging as much as you like: it will be always completely charged and ready for use when is needed. It wont be overcharged and it will not discharge. 9V Automatic Battery NiCd Charger Circuit Diagram : With the values presented in the circuit diagram, the battery charger NiCd circuit is suitable for 6V and 9V batteries. 9 volt types with 6 and 7 cells are charging with 20mA; P1 must be adjusted so that the NiCd charger disconnects after 14 hours. Window inferior level is set at 1V below this value with P2. 5V battery type with 4 or 5 cells are charged at 55mA. Again, with P1 adjust the NiCd charger circuit so it disconnects after 14 hours. Window inferior level must be set at 0.8V below this value.

Automatic AC Power Switch

for the Holiday Home Electrical appliances accidentally left on  in (holiday) homes left unoccupied for a  short or a long period consume power  unnecessarily and can present a fire hazard. Everyone will be familiar with those  nagging thoughts, a few miles down the  road from the house: “Did I remember  to switch off the coffee machine? The  lights? The oven?” Circuit diagram : Automatic AC Power Switch Circuit Diagram Hotel rooms are often equipped with a  switch near the main door which enables the power supply to everything in  the room only when the plastic card (which  might contain a chip or have a magnetic strip  or a pattern of holes) that serves as the room  key is inserted. The circuit idea given here  to switch off lights and other appliances is  along the same lines. The solution is surprisingly simple. A reed contact is fitted to the frame of the main entrance door, and a matching magnet  is attached to the door itself such that when  the door is closed the reed con...

Automatic Bicycle Light

T his  automatic  bicycle  light  makes cycling in the dark much  easier (although you still need  to pedal of course). The circuit  takes  the  ambient  light  level  into account and only turns on  the light when it becomes dark.  The light is turned off when no  cycling has taken place for over  a minute or if it becomes light  again. The biggest advantage of  this circuit is that it has no manual controls. This way you can  never ‘forget’ to turn the light  on or off. This makes it ideal for  children and those of a forgetful  disposition. Bicycle Light Image : To detect when the bicycle is  used (in other words, when the  wheels turn), the circuit uses a  reed switch (S1), mounted on  the frame close to the wheel.  A small magnet is fixed to the  spokes (similar to that used with  most  bicycle  speedometers),  which  ...

Automatic Water Tank Filler

This circuit has been very useful in filling a header tank for a reticulated water supply on a farm. Eight troughs are supplied in different paddocks where a lack of water would have serious consequences for the stock. In the past, the tank had been filled daily by a time clock which was not successful. During hot weather, the stock would empty the tank on a regular basis and then be without water for several hours or the tank would overflow and flood the area if the weather was wet and the cattle did not drink much.The circuit described has been used to maintain the level of water in the header tank within prescribed limits. It controls a 3HP submersible bore pump which has a high starting current, necessitating a solid-state relay sufficient to take the starting load. Two Darlington transistors, Q1 & Q3, in conjunction with Q2 & Q4, are connected to the upper and lower water sensors in the tank. Q2 & Q4 have a common 5.6kO load resistor and function as a NOR gate. The out...

How to build Automatic 12 Volt Lamp Fader

The circuit employs two strings of series connected lamps. One string is complimentary to the other, this means that when one string fades the other string gains luminescence. Two power transistors 2N3053 are connected in complimentary mode as shown in circuit 1. The collector of the first transistor is connected to base of the second one through a 2.2K resistor. Different type of light source can be used by calculating the line current and bias voltages. Christmas tree bulb is a good option, as this bulb takes 200mA at 4V DC. Three numbers in series thus do not require any current limiting resistance when applied voltage is 12V DC , as shown in the circuit. 2N3053 can smartly handle up to 500mA of current and hence using the same transistor three strings of LEDs can be connected in parallel with a current limiting resistance of 220ohm, as shown in circuit 2. Four LEDs will be connected in a string, each LED chain will draw around 20mA of current. Hence, in practice, using th...