Automatic Plant Irrigator

Automatic Plant Irrigator Circuit Diagram. The circuit presented here waters your plants regularly when you are out for a vacation. The circuit comprises a sensor part built using only one op-amp (N1) of quad op-amp IC LM324. Op-amp N1 is configured here as a comparator. Two stiff cop-per wires are inserted in the soil containing plants. As long as the soil is wet, conductivity is maintained and the circuit remains off. When the soil dries out, the resistance between the copper wires (sensor probes A and B) increases. If the resistance increases beyond a preset limit, output pin 1 of op-amp N1 goes ‘low’.

Automatic Plant Irrigator Circuit Diagram

This triggers timer IC2 (NE 555) configured as a monostable multivibrator. As a result, relay RL1 is activated for a preset time. The water pump starts immediately to supply water to the plants. As soon as the soil becomes sufficiently wet, the resistance between sensor probes decreases rapidly. This causes pin 1 of op-amp N1 to go ‘high’. LED1 glows to indicate the presence of adequate water in the soil. The threshold point at which the output of op-amp N1 goes ‘low’ can be changed with the help of preset VR1. To arrange the circuit, insert copper wires in the soil to a depth of about 2 cm,keeping them 3 cm apart. When the soil the water. LED1 glows up as the water reaches the probes.

For small areas a small pump such as the one used in air coolers is able to pump enough water within 5 to 6 seconds. The timing components for IC2 are selected accordingly. The timing can be varied with the help of preset VR2. The circuit is more effective indoors if one intends to use it for long periods. This is because the water from reservoir (bucket, etc) evaporates rapidly if it is kept in the open. For regulating the flow of water, either a tap can be used or one end of a rubber pipe can be blocked using Mseal compound, with holes punc-gets dried, adjust VR1 towards ground rail until LED1 turns off and relay RL1 is energised. The motor starts pumping tured along its length to water several plants.

Author: Priyank MudgaL - Copyright: Efymag

Comments

OP AMP INTEGRATOR CALCULATOR

Enter the Input Voltage,Vin: Volts Enter the Frequency, f: Hertz Enter the Input Resistance, Rin: Ohms Enter the Value of Capacitor, C: Farads Output Voltage, Vout: Volts OP AMP based Integrator Tutorial and Design

Block diagram of AM transmitter and receiver with explanation

Block diagram of AM transmitter and receiver with explanation AM Transmitter : Transmitters that transmit AM signals are known as AM transmitters. These transmitters are used in medium wave (MW) and short wave (SW) frequency bands for AM broadcast. The MW band has frequencies between 550 KHz and 1650 KHz, and the SW band has frequencies ranging from 3 MHz to 30 MHz. The two types of AM transmitters that are used based on their transmitting powers are: · High Level · Low Level High level transmitters use high level modulation, and low level transmitters use low level modulation. The choice between the two modulation schemes depends on the transmitting power of the AM transmitter. In broadcast transmitters, where the transmitting power may be of the order of kilowatts, high level modulation is employed. In low power transmitters, where only a few watts of transmitting power are required , low...

Using the TLP250 Isolated MOSFET Driver Explanation and Example Circuits

I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well...

Do More

Search This Blog