Do More

This project flashes eight LEDs in an apparently random manner. It uses a 4060 combined counter and display driver IC which is designed for driving 7-segment LED displays.  Circuit diagram : Simple 8 Random Flashing LEDs The sequence is not really random because seven of the LEDs would normally be the display segments, the eighth LED is driven by an output that is normally used for driving further counters. The table below shows the sequence for the LEDs. You can use less than eight LEDs if you wish and the table may help you decide which ones to use for your purpose.

This is an amplifier circuit based on IC AN374 which has a 1 Watt output power with supply voltage and a maximum of at least 8 volts to 16 volts with the DC current. Following amplifier circuit 1 Watt l 8 - 16 Volts Audio Amplifier. 1 Watt l 8 - 16 Volts Audio Amplifier

This circuit use TA7222AP to amplifiers audio signal .The price only $0.99 and can provide 5.8 watt with Muting Control.Power supply can use for 8-12Vdc it is a good idea to use for car audio power amp , coin-op machine game, security system etc. link Fig 1. TA7222AP pin out Pin Name Description 1 Vcc Supply Voltage 2 RR Ripple Reject 3 MC Muting control 4 OP AF Signal Input 5 FB FB Filter 6 GA Gain adjust 7 GND Ground 8 GND Ground 9 OP AF Output 10 BS BootStrap Fig 2. schematic for 5.8 watt audio power amplifier

This power supply is powered by a transformer operating from 120 Vac on the primary and providing proximately 20 Vac on the primary, and providing approximately 20 Vac on the secondary. Four 10-A diodes with a 100 PIV rating are used in a full-wave bridge rectifier.  8-Amp Regulated Power Supply Circuit Diagram A 10,000 ^F/36 Vdc capacitor completes the filtering, providing 28 Vdc. The dc voltage is fed to the collectors of the Darlington connected 2N3055's. Base drive for the pass transistors is from pin 10 of the µ723 through a 200 ohm current limiting resistor, Rl. The reference terminal (pin 6) is tied directly to the non-inverting input of the error amplifier (pin 5), providing 7.15 V for comparison. The inverting input to the error amplifier (pin 4) is fed from the center arm of a 10 k ohm potentiometer connected across the output of the supply. This control is set for the desired output voltage of 13.8 V. Compensation of the error amplifier is accomplished with a 500 pF cap...

GE Intelligent Platforms is pleased to announce the availability of CIMPLICITY Version 8.1, the latest addition to our family of HMI/SCADA products. Version 8.1 maximizes the power of your information with new innovative for both the development and runtime environments. Change Approval/eSignature - Achieve regulatory compliance, avoid regulatory penalties and conform with good manufacturing practices by using the new change approval feature. This feature delivers an audit trail, approval before operating, multi-signature and commenting capabilities. Alarm variable association -    CIMPLICITY 8.1 brings a new ability to easily log up to 6 additional points when an alarm occurs or changes state. This information can be easily viewed in the A&E table and in the historical alarm viewer which enables instant analytics for quick operator resolution. More flexible classes - 8.1 introduces enhancements that enable more flexible classes which speed new product developm...

This circuit uses a NE555 timer and CD4020B. When +12 Vdc is applied to the circuit, the output of IC2 is set low via C2, which turns on the relay, and IC1, a pulse generator. Auto Turn-Off Alarm With 8-Minute Delay Circuit Schematic IC1 pulses counter IC2. After 8192 clocks, IC2 output (pin 3) goes high, cuts off Q2, and completes the cycle.

This is a Simple Auto Turn-Off Alarm With 8-Minute Delay Circuit Project. This circuit uses a NE555 timer and CD4020B. When +12 Vdc is applied to the circuit, the output of IC2 is set low via C2, which turns on the relay, and IC1, a pulse generator. IC1 pulses counter IC2. After 8192 clocks, IC2 output (pin 3) goes high, cuts off Q2, and completes the cycle. Simple Auto Turn-Off Alarm With 8-Minute Delay Circuit Diagram

This circuit use TA7222AP to amplifiers audio signal .The price only $0.99 and can provide 5.8 watt with Muting Control.Power supply can use for 8-12Vdc it is a good idea to use for car audio power amp , coin-op machine game, security system etc. Fig 1. TA7222AP pin out Pin Name Description 1 Vcc Supply Voltage 2 RR Ripple Reject 3 MC Muting control 4 OP AF Signal Input 5 FB FB Filter 6 GA Gain adjust 7 GND Ground 8 GND Ground 9 OP AF Output 10 BS BootStrap Fig 2. schematic for 5.8 watt audio power amplifier

Simple 10 Amp 13.8 Volt Power Supply Circuit Diagram. Sometimes amateurs like to home-brew their power supplies instead of purchasing one off the shelf at any of the major ham radio retail dealers. The advantage to rolling your own power supply is that it teaches us how they work and makes it easier to troubleshoot and repair other power supply units in the shack. It should be noted that there is no real cost advantage to building your own power supply unless you can get a large power transformer and heat sink for a super low price.  Of course rolling our own gives us the ability to customize the circuit and make it even more reliable than commercial units. The circuit in Figure 1 will give us 10 amps (12 amps surge) with performance that equals or exceeds any commercial unit. The circuit even has a current limiting feature which is a more reliable system than most commercial units have. Just like other commercial units, this circuit uses the LM723 IC which gives us excellent volta...

This is Low power amplifier , based on IC TDA2824 product of Philips. Maximum output is about 2 X 1,8 Watt , these include low  output amplifier type. Minimum required voltage 3 Volts and maximum voltage of 18 volts DC. Specification : Supply Voltage : 3 - 18 Volts Power Output   : 2 x 1,3 Watts RL impedance  : 4 Ohms Frequency responses : 30Hz -18kHz Quiescent current : 6 mA