Do More

This is very simple circuit diagram of  Half wave AC Phase Controlled Circuit.  The 5AH will trigger when the voltage across the two 0 juF capacitors reaches the breakdown voltage of the lamp. Half wave AC Phase Controlled Circuit Diagram: Control can be obtained full off to 95% of the half wave RMS output voltage Full power can be obtained with the addition of the switch across the SCR.

This Laser Controlled ON/OFF switch circuit is built around a 555 timer using very few components. Since the circuit is very simple, even a novice can easily build it and use it as a controlling device. A laser pointer, now easily available in the market, can be used to operate this device. This circuit has been tested in operational conditions from a distance of 500 meters and was found to work satisfactorily,though it can be controlled from still longer distances. . Laser Controlled ON/OFF switch Circuit diagram : Laser Controlled ON/OFF Switch Circuit Diagram Aiming (aligning) the laser beam exactly on to the LDR is a practical problem. The circuit is very useful in switching on/off a fan at night without getting off the bed. It can also be used for controlling a variety of other devices like radio or music system. The limitation is that the circuit is operational only in dark or dull lit environments. By focusing the laser beam on LDR1 the connected gadget can be activated throug...

Audio Controlled Mains Switch Circuit diagram. It is often useful for audio or video equipment to be switched off automatically after there has been no input signal for a while. The function of the on-off switch in such equipment is then taken over by switch S2 in the accompanying diagram. It remains, however, possible to  switch off manually by means of Si. Automatic  switch-off occurs after there has been no input  signal for about 2 minutes: this delay makes it possible for a new record or cassette to be placed in the  relevant machine.   The audio input to the proposed circuit may be  taken from the output of the relevant TV set, amplifier, or whatever. The input earth is held at + 6 V  with respect to the circuit earth by potential divider  Ri-R2-R3-R4. The two 741s function as comparators: the output of ICi goes high when the in- put signal is greater than + 50 mV, whereas the out- put of IC2 goes high when the input signal  becomes mor...

The objective of this instructable is to guide your way throw the entire making process of building a BuildersBot machine. An Arduino controlled CNC Router that can also perform 3D printing. The instructions will cover all areas such as, mechanics, electronics and software. [ ]

             This project is a robot vehicle that can be controlled through any computer wirelessly using a WiFi link. It transmits real-time video to the controlling computer using the same link. The video transmitting camera mounted on it. It also has obstacle detection,temperature,sound and light sensitivity feature.           Usually robots are controlled through a laptop using an WiFi link which is subject to attenuation, noise and has a very limited range as well. This project features a robot that uses WiFi 802.11G standard for its control signals through TCP/IP protocol, which has flow control. This enables uninterrupted and reliable transmission of control signal to the robot vehicle. WiFi support high data rates which enables good quality uninterrupted video transmission from the robot to the computer. Image capturing is done by mounting an IP-camera over the Robotic Car. Obstacle detection is done...

Build a Simple Voltage Controlled Oscillator Circuit Diagram . This circuit is a voltage-controlled oscillator, which is an oscillator whose frequency is determined by a control voltage. With the component values shown, the oscillator has a frequency of 8 kHz.   Voltage Controlled Oscillator Circuit Diagram When an input signal is applied to the base of Ql the current flowing through Ql is varied, thus varying the time required to charge Cl. Due to the phase inversion in Ql the direction of output frequency change is 180 degrees out of phase with the input signal The output may be used to trigger a bistable flip-flop.

Circuit diagram This circuit is a 73 MHz Hallogene Lamp Radio-Controlled. The purpose of it is to control the power state of a hallogene lamp by a remote control. When we press the push botton of the remonte control, the power state of the lamp will be changed, so, if the lamp was turned on, it will turned off and if it was turned on, it will turned off. If we press to the button another time, the same action will be occured. When the button is pressed, a LED indicator lights on the remote control. The system is consisted by two separate circuit. One is the remote control, or the emmetor. The other is the receptor, or the hallogene lamp controller. We plug the input of the lamp controller circuit to the 120VAC source of the sector to supply it. The lamp must be pluged to the output of the circuit to be supplied and controlled. The controller circuit has also an antenna to receive the signal of the remote control. The remote control has also an antenna to transmit the signal to the cont...