Skip to main content

Posts

Showing posts with the label Single

Single Transistor Relay Toggle

The circuit below requires a double pole, double throw relay in conjunction with a single transistor to allow toggling the relay with a momentary push button. One set of relay contacts is used to control the load, while the other is used to provide feedback to keep the relay activated or deactivated. Several push buttons can be wired in parallel to allow toggling the relay from different locations. In the deactivated state, the relay contacts are arranged so the 1000 uF capacitor will charge to about 2.7 volts. When the switch is closed, the capacitor voltage is applied to the transistor base through a 560 resistor causing the transistor to turn on and activate the relay. In the activated state, the relay contacts are arranged so the 3.3K resistor and 560 ohm resistor provide a continous current to the transistor base maintaining the activated state. While in the activated state, the capacitor is allowed to discharge to zero through the 1K resistor. When the switch is again closed, the...

Explanation of Single Phase Induction Type Energy Meter

Single Phase Induction Type Energy Meter Single phase induction type energy meters are extensively used for the measurement of electrical energy in single phase A.C circuits. One can find such meters installed in homes. It is also called as single phase watt-hour meter. Single Phase Induction Type Energy Meter Principle: torque is produced to rotate the disc is due to interaction of two fluxes. Since the e.m.f induced in the disc by induction, this instrument operates on A.C only. Construction: The below fig shows the various parts of a single phase induction type energy meter. It consists of a shunt magnet, a series magnet, a rotating disc, a brake magnet and a counting mechanism. The shunt magnet consist of a number of M shaped iron laminated core wound with a fine wire of many turns i.e. coils and is connected across the supply. The shunt coil carries a current proportional to supply voltage and is known as Pressure coil . The flux produced by shunt magnet lags behind the supply v...

What is SMART Single Module Auto Ranging Transmitter Device

  This term was coined by Honeywell, USA in 1985. The first generation of instruments like flow meters were mechanical devices. The next generation used electronics for improving performance. With electronics, adjustment of range, span, zero adjustment etc. could be carried out with potentiometers. (i.e. ease of setting parameters was achieved) In some cases functions like linearization, annunciation (exceeding process limits) etc. were also integrated. With the help of 4-20mA transmitter, data transmission over longer distance was made easy. There was a considerable jump in technology in terms of improved accuracy, response, interface with operator, ease of adjustment of range and span. This was made possible with use of digital circuits, microcontrollers, ADC, DAC. Today we hear about not only Smart Transmitter/Instruments, but Smart Control Valves, Smart Machines like Microwave Ovens, Washing Machines etc. Digital Oscilloscope also can be categorized as Smart Oscilloscope. Most...

TDA7012T Single chip FM received

FM Radio Receiver IC TDA 7012T is very simple, but Radio This FM receiver has good sensitivity and selectivity. Single Chip TDA 7012T FM Receifer is to build an FM receiver requires a few additional components. Feature contained in FM receiver IC TDA 7012T is quite tempting to an FM receiver. Among features an FM receiver TDA 7012T is a low-voltage applications micro affability arrangement (MTS), Frequency Loked Loop (FLL) to 76 KHz range and selectivity of FM receiver with RC Filter. In an article by FM Radio Receiver IC TDA 7012T can be seen in the FM receiver circuit which can be made​​. TDA7012T- Mini FM received Schematic Part List R1 = 8kΩ2 R2 = 10kΩ R3 = 390Ω C1,C3 = 10nF C2,C6,C9,C16 = 100nF C4 = 33pF C5 = 25pF trimmer C7,C10 = 1nF5 C8 = 820pF C11 = 1nF C12 = 68pF C13 = 220pF C14 = 47μF 10V C15 = 3nF3 L1 = 36nH L2 = 1μH, IC1 = TDA7021T

Single IC Dual tones Siren Circuits Diagram

This circuit is intended for children fun, and can be installed on bicycles, battery powered cars and motorcycles, but also on models and various games and toys. With SW1 positioned as shown in the circuit diagram, the typical dual-tone sound of Police or Fire-brigade cars is generated, by the oscillation of IC1A and IC1B gates. With SW1 set to the other position, the old siren sound increasing in frequency and then slowly decreasing is reproduced, by pushing on P1 that starts oscillation in IC1C and IC1D.  The loudspeaker, driven by Q1, should be of reasonable dimensions and well encased, in order to obtain a more realistic and louder output. Tone and period of the sound oscillations can be varied by changing the values of C1, C2, C5, C6 and/or associated resistors. No power switch is required: leave SW1 in the low position (old-type siren) and the circuit consumption will be negligible. Single -IC Dual-tones Siren Circuits Diagram Parts: R1 ,R3 ___470K    1/4W Resistors...