Skip to main content

Posts

Showing posts with the label NiCd

Cheap cost Universal charger for NiCD NiMH batteries Circuit Diagram

This is the very simple and Cheap cost Universal charger for NiCD - NiMH batteries Circuit Diagram. This circuit is ideal for car use. It has ability to transform a mains adapter for the charger. This can be used to recharge cell phones, toys, video batteries, MP3 players, ... and is selectable charging current. A LED is located in the circuit to indicate charging. Can be built on a breadboard or a general purpose PCB. Hope you like it. Universal charger for NiCD - NiMH batteries Circuit Diagram Parts: R1 = 120R-0...5W R2 = See Diagram C1 = 220uF-35V D1 = 1N4007 D2 = 3mm. LED Q1 = BD135 J1 = DC Input Socket Specifications: Ideal for in car use. LED charge indication. Selectable charge current. Charges Ni Cd or NiMH batteries. Transforms a mains adapter into a charger. Charge cellular phone, toys, portables, video batteries … Features: LED function indication. Power supply polarity protected. Supply current: same as charge current. Supply voltage: from 6.5VDC ...

9V Automatic Battery NiCd Charger

This automatic NiCd charger for 9V NiCd batteries is using 555 timer properties and is very easy to build. Why is an automatic 9 volts NiCd battery charger? Because you can leave the battery for charging as much as you like: it will be always completely charged and ready for use when is needed. It wont be overcharged and it will not discharge. 9V Automatic Battery NiCd Charger Circuit Diagram : With the values presented in the circuit diagram, the battery charger NiCd circuit is suitable for 6V and 9V batteries. 9 volt types with 6 and 7 cells are charging with 20mA; P1 must be adjusted so that the NiCd charger disconnects after 14 hours. Window inferior level is set at 1V below this value with P2. 5V battery type with 4 or 5 cells are charged at 55mA. Again, with P1 adjust the NiCd charger circuit so it disconnects after 14 hours. Window inferior level must be set at 0.8V below this value.

NiCd Battery Charger Circuit Diagram

The design of the charger is similar to that of many commercially available chargers. The charger consists of a mains adaptor, two resistors and a light-emitting diode (LED). In practical use, this kind of charger is perfectly all right. Resistor R1 serves two functions: it establishes the correct charging current and it drops sufficient voltage to light the diode. This means that the LED lights only when a charging current flows into the battery. The charging current is about 1/4 of the battery capacity, which allows a slight overcharging, and yet the charging cycle is not too long (4–5 hours). Circuit diagram: The value of the resistors may be calculated as follows, for which the nominal e.m.f. and the capacity of the battery must be known. Adjust the output of the mains adaptor to 1.17 times the nominal battery voltage plus 3.3 V, which is the potential across R1. Note that the adaptor must be capable of supplying a current of not less than half the battery capacity. The value of R1...

Advanced Linear NiMH NiCd Fast Battery Charger

This is a simple Batteries charger for NiMH/NiCd.It Requires No Microcontroller or any Firmware .Linear Technology Corporation introduces the LTC4060, an autonomous 1- to 4-cell, 0.4A to 2A linear NiMH and NiCd battery charger. The LTC4060 includes all the functions required for a battery charger circuit, operating without the aid of a microcontroller or firmware. The design is simple and needs only three passive components. The LTC4060 also eliminates the need for a sense resistor and blocking diode, which increases efficiency and lowers the solution cost. This IC is targeted at applications including portable medical equipment , automotive diagnostic systems and industrial/telecom test devices. Features Complete Fast Charger Controller for Single, 2-, 3- or 4-Series Cell NiMH/ NiCd Batteries No Firmware or Microcontroller Required Termination by –?V, Maximum Voltage or Maximum Time No Sense Resistor or Blocking Diode Required Automatic Recharge Keeps Batteries Charged Programmabl...

Smart Fast Battery Charger for NiCd NiMH

The project utilizes MAX712/MAX713 fast charge controllers in order to build a smart & fast NiCd/NiMH battery charger.   The MAX712 is designed for NiMH batteries and the MAX713 is for NiCd batteries where the battery-fully-charged sensing method is the only difference between them. The values for some of the components included in the circuit can be chosen using the reference from Maxim. Depending on the number of cells of the battery pack intended to charge as well as the charging time, those values may vary. The charger won’t be able to charge packs with more than six 1.2V cells if it is powered only with 12V. the MAX will get hot and the charging current won’t be what is expected from the value of the sensing resistor if something bigger than 12V would be tried. This is due to the sinking of as much current as possible from the base of the power transistor as it tries to obtained up to 250mV voltage drop on the sensing resistor. The timer feature of MAX712/713 cannot be di...