Skip to main content

Posts

Showing posts with the label How

How light dimmers work

Light dimming is based on adjusting the voltage which gets to the lamp. Light dimming has been possible for many decades by using adjustable power resistors and adjustable transformers. A light dimmer works by essentially chopping parts out of the AC voltage. This allows only parts of the waveform to pass to the lamp. The brightness of the lamp is determined by the power transferred to it, so the more the waveform is chopped, the more it dims. Solid-state light dimmers work by varying the “duty cycle” (on/off time) of the full AC voltage that is applied to the lights being controlled. For example, if the voltage is applied for only half of each AC cycle, the light bulb will appear to be much less bright than when it get the full AC voltage, because it get’s less power to heat the filament. Solid-state dimmers use the brightness knob setting to determine at what point in each voltage cycle to switch the light on and off. Typical light dimmers are built using thyristors and the exact tim...

How to build Solar Cell Voltage Regulator

Description This device is designed to be a simple, inexpensive ‘comparator’, intended for use in a solar cell power supply setup where a quick ‘too low’ or ‘just right’ voltage indicator is needed. The circuit consists only of one 5V regulator, two transistors, two LEDs, five resistors, two capacitors, and one small battery. Although a 4-V battery is indicated, 4.5 V (3 alkalines in series) or 3.6 V (3 NiCd cells in series) will also work. The specifications of voltage regulator IC1 are mainly determined by the size and number of the solar cells and the current pull of the equipment connected to the output. Here the low-drop 4805 is suggested but other regulators may work equally well as long as you observe the output voltage of the solar cells. Transistors T1 and T2 are complementary types i.e. one each of the pnp and npn variety. Circuit diagram: Although the ubiquitous BC557B (pnp) and BC547B (npn) are indicated, any small-signal equivalents out of the junk box will probably do....

How to check TV Flyback

There are actually several kinds of tools that can be used for check whether flybak damaged. But we have a simple way we have always done for ascertain whether flybak damaged or is still good, before replacing the horizontal transistor. All it takes is a light bulb with an added Exciter 100Watt cable connection along approximately 25cm. The trick determine if flyback damaged or is still good is as follows : Break up the relationship between the collector of transistor horizontal flyback-out. By (a) Open collector aspirated by means of the printed board solder, or (b) Remove the jumper cables if any, or (b) Cutting prited path. Ac volt-meter pairs of horizontal transistor base with a ground out. Turn on the plane a little while - there must be an ac voltage of about 1v. This is done is for ensure that the horizontal oscillator and driver are working horizontally. Replace light bulb between the collector of transistor flyback horizontal (light diseri the collector). Turn on the plane...

How to Make a Solar Top Robot 1

Here is Simple Electronic Solar Project of  Top Robot (1) Make a Robot is not easy, but also not very difficult. Here we start from an easy example – Solar Top. It has below function: Rotator under sunshine Come back if meet Obstacle Keep stay in no sunshine place. This is a simple automatic robot. It don't need people maintance. The life is depend on the environment and mechanical wear. The parts cost is very low. The following is the parts you need: Clip  6 units Mini Motor  1 unit Capacitor  3 units NPN Triode  1 unit PNP Triode  1 unit 2.2K resistance  1 unit LED light 1 unit Some Wire Small Solar Panel ( >4V, 10mA)  1 unit Some Solder Wire Perforated Board 1 unit Below is the robot circuit diagram:

How to Make a PWM Lamp Dimmer Using NE555

A simple and efficient PWM lamp dimmer using timer IC NE555 is discussed in this article. Yesterdays linear regulator based dimmers can only attain a maximum efficiency  of 50% and are far inferior when compared to the PWM based dimmers which can hit well over 90% efficiency. Since less amount of power is wasted as heat, the switching elements of PWM dimmers require a smaller heat sink and this saves a lot of size and weight. In simple words, the most outstanding features of the PWM based lamp dimmers are high efficiency and low physical size. The circuit diagram of a 12V PWM lamp dimmer is shown below. We recommend 3 very good books to learn the basics and applications of the 555 timer IC. These books have been thoroughly reviewed and they can be purchased by clicking on this link:- 3 Great Books to Learn 555 Timer Circuits and Projects Fig 1 : PWM lamp dimmer using NE555 As you can see, NE555 timer IC which is wired as an astable multivibrator operating at 2.8KHz forms the heart ...

How to drive a latching relay

Latching relay (a.k.a. impulse relay) can be turned on and off by momentarily applying a voltage across the relay coil. The relay would maintain in its last switched state without the need to maintain the coil current. In this post, I will show a simple circuit which can be used to drive such relays. In the video towards the end, I also included more explanations and some demonstrations. The relay I am using here is a latching RF relay. It is used to switch the input signal between its two outputs. For this particular relay, the input has an APC-7 connector. One side of the output has an N connector and the other side is 50 Ohm terminated. Although this relay is an RF relay, the method I described below is applicable to any latching relays. Many dedicated ICs (such as MAX4820, MAX4821) can be used for driving such relays. Because of nature of the latching relay, no H-bridge is needed (although you can definitely use an H-bridge, but it would be wasteful). [ ]

How electricity is generated Reviews Exercises

5.10 How electricity is generated Reviews Exercises 1. Define the term “generator." 2. State the three major parts of a direct current generator. 3. With the aid of a sketch, explain how e.m.f. is induced in a direct current generator. 4. Explain how a simple direct current generator may be improved for greater e.m.f. induction. 5. Define the term ''piezoelectricity." 6. With the aid of sketches, explain how thermocouples may be used to produce a higher voltage. 7. Explain how solar cells produce electricity. 8. List three applications of solar cells in everyday life. 9. State two uses of geothermal energy.

Theory of Capacitive Proximity Sensors How they Works

Theory of Capacitive Proximity Sensors | How Capacitive Proximity Sensors Works? This knowledge of Sensors will help you better understand customer applications. In addition, you will be better able to describe products to customers and determine important differences between products. You should know Basics of Electricity and Basics of Control Components before attempting Sensors.  Today we learn the Theory of Capacitive Proximity Sensors and how they work? Let’s Start. Capacitive proximity sensors are similar to inductive proximity sensors. The main difference between the two types is that capacitive proximity sensors produce an electrostatic field instead of an electromagnetic field . Capacitive proximity switches will sense metal as well as nonmetallic materials such as paper, glass, liquids, and cloth. The sensing surface of a capacitive sensor is formed by two concentrically shaped metal electrodes of an unwound capacitor. When an object nears the sensing surface it ente...