Do More

This is a Variable 5 to 20V DC Supply Circuit Diagram . If you are looking for a low drop voltage regulator that can provide a power supply of 1A with an output voltage of between 5V and 20V DC, National Semiconductor LM2941 Low Dropout Adjustable Regulator is that you can pick to make use of. It's a typical dropout voltage of 0.5V which means that the input supply need only must be 0.5V DC over the desired output voltage.  Variable 5 to 20V DC Supply Circuit Diagram   Its other features include internal short circuit current limit and reverse battery protection. As shown in the schematic below, the regulator has five pins which consists of the ON/OFF control, Input Voltage, Output Voltage, Ground & Adjustable pins. ON/OFF is used for the purpose of switching on & off of the regulator. The capacitors C1 & E1 are to be placed as close as feasible to the regulator.  The output of the circuit can be varied by varying the worth of potentiometer VR1 from 5V DC to 2...

This is very simple electronic circuit project of dual step-down power-supply (smps) controller circuit using the MAX17031. Dual step-down power-supply (SMPS) controller can be designed a very simple high efficiency power supply circuit with synchronous rectification, intended for main 5V/3.3V power generation in battery-powered systems. Dual Step-Down Power-Supply (SMPS) Controller Circuit Diagram: Low-side MOSFET sensing provides a simple low-cost, highly efficient current sense for valley current-limit protection. Combined with the output overvoltage and undervoltage protection features, this current limit ensures robust output supplies. The device includes independent shutdown controls with well-defined logic thresholds to simplify power-up and power-down sequencing. To prevent current surges at startup, the internal voltage target is slowly ramped up from zero to the final target over a 1ms period. The Max17031 can be used in applications like : Notebook Computers , Ultra-Mobile P...

Power supply circuit to generate output below were variations between 1.3V DC to 12.2V DC with 1A current. In addition, the power supply circuit is also equipped with over-current protection or shield against belebih flow. Power supply circuit is very simple, but the quality is quite good, made her basiskan regulator IC LM723 is a pretty legendary. Description: R2 to set the output voltage. The maximum current is determined by R3, over-current protection circuit inside the LM723 to detect the voltage on R3, if it reaches 0.65 V, the voltage output will be off her. So the current through R3 can not exceed 0.65 / R3 although output short-circuit in his. C3 and C4 are ceramic capacitors, as much as possible directly soldered to the PCB, this is because the LM723 is prone to oscillation that is not cool. LM723 works with 9.5V input voltage to 40 V DC and the LM723 can generate its own current of 150mA when the output voltage is not more than 6-7V under input voltage. Specifications: Output...

This Bipolar power supply for battery instruments . This is a simple circuit diagram, this circuit to generate regulated ± 5-V supplies from a pair of dry batteries, the circuit of Fig. 1 is commonly used. In order to give protection from inadvertent reverse connection of a battery, a diode in series with each battery would produce an unacceptable voltage drop.  The more effective approach is to fit diodes Dl and D2 as shown in Fig. 2, in parallel with each battery. When the supply is switched off, there is the risk of a reverse bias being applied across the regulators, if there is significant inductance or capacitance in the load circuit. Diodes across the regulators prevent damage. When the power supply is switched on, the two switches do not act in unison.   Bipolar Power Supply Circuit Diagram There is a probability that one or the other regulators will be latched hard off by the other. To prevent this, D3 and D4 are Zener diodes so that ± 5-V rails are pulled up by...

The output voltage from the input voltage is an interesting property is appreciably lower switching power supply: It's produced by the current is smaller than the output current. However, input power (UI), of course, is higher than the output power. On the switch when low input voltage is too low, the regulator try to draw full current will need to be looked at another aspect. Supply can not cope with it, if it fails or the fuse blows. It (On / Off by input) switch to disable the regulator reduced, so is advisable. Related capacitor is charged until. If the regulator starts to draw current, charging current overload voltage source which is not already on a level declined. Soft Start For Switching Power Supply Circuit Diagram: The circuit in the diagram provides an output voltage of 5 V and is supplied by a 24 V source. The regulator need not be disabled until the capacitor is fully charged: when the potential across the capacitor has reached a level of half or more of the input vol...

Power supply with driver TEA1507 is mostly used by TV branded PHILIPS. Power Supply has an efficiency rate of up to 90% - thus requiring less cooling, as well as stand-by power required is less than 1 watt. Power Supply with TEA driver is equipped with a variety of surge protector that has a high reliability - not easily damaged if any part of a damaged power supply circuit and power transistor or FET heat is not easily damaged. Power supply circuits are dapatapat working on ac input voltage between 85 up to 275v. The way it works with the driver circuit power supply TEA 1507 is quite simple, so easy tracking of damage to the circuit. The picture above is the basic power supply circuit with TEA1507

This 200W power amplifier circuit using IC STK 4050. STK 4050 is a power amplifier module is very powerful, because the IC is already a module then only needed a little extra components to build a reliable 200W Power Amplifier. Here is a picture series of Power Amplifier ICs 200W use STK 4050 complete with its power supply:

                                           This is the circuit diagram of 5V DC regulated power supply which featured with short circuit protection system. There are 2 kind of output that are regulated 5V DC with short circuit protection and without circuit protection. The main circuit is protected from any damage due to short-circuit in the additional power supply circuit by cutting off the derived supply voltage. The derived supply voltage restores automatically when shorting is removed. An indicator LED is utilized to show whether short-circuit exists or not. Power Supply Block: This circuit works just like the ordinary DC power supply adapter, in the main power supply circuit, 230V AC from main home electric source is stepped down by transformer X1 (230V AC primary to 0-9V, 3...

This is definitely an effective 4-output stage stabilized DC power supply unit for testing electronic circuits. It delivers very well regulated and stabilised output, that is important for most electronic circuits to provide good results. The circuit gives you an audio-visual indication if there is a short circuit in the PCB under test, so the power supply to the circuit ‘under test’ could be cut-off instantly to protect the important components from damage. The circuit gives you four different regulated DC outputs (12V, 9V, 6V and 5V) and an unregulated 18V DC output, that are selectable by way of rotary switch S2. The selected output is showed on the analogue voltmeter connected to the outputs rails. The circuit works by using a typical 18V-0-18V, 500mA step-down transformer to deliver 18V AC. A rectifier diode comprising diodes D1 and D2 supplies 18V DC, that is smoothed by capacitor C1 and given towards the combination of regulator ICs (IC1 through IC4). The regulator ICs deliver ...

Description An increasing number of appliances draw a very small current from the power supply. If you need to design a mains powered device, you could generally choose between a linear and a switch-mode power supply. However, what if the appliance’s total power consumption is very small? Transformer-based power supplies are bulky, while the switchers are generally made to provide greater current output, with a significant increase in complexity, problems involving PCB layout and, inherently, reduced reliability.  Is it possible to create a simple, minimum part-count mains (230 VAC primary) power supply, without transformers or coils, capable of delivering about 100 mA at, say, 5 V A general approach could be to employ a highly inefficient stabilizer that would rectify AC and, utilizing a zener diode to provide a 5.1 V output, dissipate all the excess from 5.1 V to (230×v2) volts in a resistor. Even if the load would require only about 10 mA, the loss would be approximately 3 watts...

This power supply is powered by a transformer operating from 120 Vac on the primary and providing proximately 20 Vac on the primary, and providing approximately 20 Vac on the secondary. Four 10-A diodes with a 100 PIV rating are used in a full-wave bridge rectifier.  8-Amp Regulated Power Supply Circuit Diagram A 10,000 ^F/36 Vdc capacitor completes the filtering, providing 28 Vdc. The dc voltage is fed to the collectors of the Darlington connected 2N3055's. Base drive for the pass transistors is from pin 10 of the µ723 through a 200 ohm current limiting resistor, Rl. The reference terminal (pin 6) is tied directly to the non-inverting input of the error amplifier (pin 5), providing 7.15 V for comparison. The inverting input to the error amplifier (pin 4) is fed from the center arm of a 10 k ohm potentiometer connected across the output of the supply. This control is set for the desired output voltage of 13.8 V. Compensation of the error amplifier is accomplished with a 500 pF cap...

Occasionally you come across some unusual  situations when setting up measurement  systems. The author once had to set up a system to register the vibrations and strain supposed to be  present in a contactor that operated at a voltage of 25 kVAC. One of the biggest problems with this project turned out to be the power supply for  the measurement system. Since it required  a power of about 30 W it wasn’t possible to  use batteries since the system had to operate  for many hours at a time. A logical solution  would seem to be to use an isolating trans-former, but still.25 kVAC means a peak volt-age approaching 40 kV, and on top of that  you would have to include a safety margin. In  addition, everything that is connected to high  voltage lines should also be able to withstand  lighting strikes! Circuit diagram : Power Supply with High Voltage Isolation Circuit Diagram Consequently the isolation should be able to  cope wit...

This circuit is a switching power source , or SMPS , it is based on the MC33374 integrated circuit , which is a switching voltage regulator high power manufactured by Motorola Semiconductor . This switching power supply circuit using the MC33374 will provide a maximum power of around 90 W and requires few external components .  Power Supply Switched 15V x 6A Circuit Diagram The MC33374 is an IC designed to operate directly from a rectified supply line , with a fixed input AC 100 V, 115 V or 230 V, and more than 90 W with a variable AC input varies from 85 V to 265 V.  If you liked this ,Take a few Seconds to Share this and leave comments

Switching Power Supply in this article are able to supply power 90 Watt. Switching Power Supply series is built directly from an AC network system using special IC MC33374 switching power supply in the form of High Voltage Power Switching Regulator and with external components to the other. IC MC33374 IC is a switching power supply designed to operate with an AC voltage source and works as a power switching converter with flyback technique. Switching Power Supply Series has a 15 volt DC output with current up to 6 Ampere. 90 Watt Switching Power Supply Schematic Series 90 Watt Switching Power Supply works by menyearahkan AC source is then used to activate the converter MC33374 system. The output of transformer switching converter MC33374 searahkan again later on as a DC voltage supply to be used for electronic devices.

The supply receive from 220 /120/110 Volt AC , then lowered by the transformer . Then receives +20 Volts DC from rectifier / filter section. This applied to pin 11 and 12 of the IC uA723/LM723 , as well as to the collector of the 2N3055 series pass transistor. The output through R1 and R2, providing about 7 V with respect to ground at pin 4. The reference terminal at pin 6 is tied directly to pin 5 , the non inverting input of the error amplifier . For fine trimming the output voltage , a potentiometer can be installed between R1 and R2. A 100-pF capacitor from pin 13 to pin 4 furnishes gain compensation for the amplifier. Base drive to the 2N3055 pass transistor is furnishes by pin of the uA723. Since desired output of the supply is 1 Ampere, maximum current limit is set to 1,5 Ampere by resistor Rsc whose value is 0,422 Ohm. A 100uF electrolytic capacitor is used for ripple voltage reduction at the output. A 1 kOhm output resistor provides stability for the power supply under no - lo...

This circuit was originally designed to power a motorcycle intercom from the vehicle supply system. This type of intercom, which is used for communication between driver and passenger, generally requires quite a bit of power. In order to improve intelligibility there is often elaborate filtering and a compander is sometimes used as well. The disadvantage is that a battery doesn’t last very long. You could use rechargeable batteries, of course, but that is often rather laborious. It seems much more obvious to use the motorcycle power supply instead. A 9-V converter for such an application has to meet a few special requirements. For one, it has to prevent interference from, for example, the ignition system reaching the attached circuit. It is also preferable that the entire circuit fits in the 9-V battery compartment. This circuit meets these requirements quite successfully and the design has nonetheless remained fairly simple. In the schematic we can recognize a filter, followed by a vo...

This clever design uses 4 diodes in a bridge to produce a fixed voltage power supply capable of supplying 35mA. All diodes (every type of diode) are zener diodes. They all break down at a particular voltage. The fact is, a power diode breaks down at 100v or 400v and its zener characteristic is not useful.  But if we put 2 zener diodes in a bridge with two ordinary power diodes, the bridge will break-down at the voltage of the zener. This is what we have done. If we use 18v zeners, the output will be 17v4. When the incoming voltage is positive at the top, the left zener provides 18v limit (and the left power-diode produces a drop of 0.6v).  This allows the right zener to pass current just like a normal diode but the voltage available to it is just 18v.  The output of the right zener is 17v4. The same with the other half-cycle.  The current is limited by the value of the X2 capacitor and this is 7mA for each 100n when in full-wave (as per thiscircuit). We have 10 x 100n = 1u capacitance....

This is smart High Voltage Power Supply 10kV Circuit Diagram. Be very carefull with this power supply because uses 220V mains and has 10KV at output. Characteristics: supply: 220V AC 50Hz mains Power: 15 Watts Ignition Voltage: 8KV . High Voltage Power Supply 10kV Circuit Diagram Sourced By: Circuitsstream