Skip to main content

Posts

Showing posts with the label Driver

Charge Pump LED Driver Using CAT3649

A very simple LED driver electronic project can be designed using the CAT3649 high efficiency quad mode R fractional charge pump IC that can drive up to six LEDs. The inclusion of a 1.33x fractional charge pump mode increases the device efficiency by up to 10% over traditional 1.5x charge pumps with no added external capacitors.Low noise input ripple is achieved by operating at a constant switching frequency which allows the use of small external ceramic capacitors. The multi−fractional charge pump supports a wide range of input voltages from 2.4 V to 5.5 V. The LED current can be adjusted in different ways. The full−scale LED current is set to 25 mA once the device is enabled. Analog dimming in 32 linear steps is achieved via a 1−wire pulse−dimming input (ADIM) Further adjustment of the LED current can be done by applying a pulse width modulation (PWM) signal on the PWM input.The CAT3649 can be shut down by holding the ADIM or PWM input in a logic low condition for greater than 30 ms....

Controlling switch with relay driver

The circuit above is  a circuit of drivers to control high voltage using the relay. Relay is controlled by an NPN transistor , its that works on 5V voltage and has diode in it, if the relay does not have s diode should be given with diode 1N4007 . Pin relay to  move the switch connected to V+ 5V and other is connected from driver NPN transistor , the base od the transistor may have input such us from circuit of infrared to control the distance, or with some other input. After the transistor was input  and the collector had output a voltage of the switch relay will work, and voltage that in switch relay ready to use. To cut off switch eliminates enough voltage input at the base transistor , the collector will not remove the voltage , and switch are automatically disconnected.

Power supply with driver TEA1507

Power supply with driver TEA1507 is mostly used by TV branded PHILIPS. Power Supply has an efficiency rate of up to 90% - thus requiring less cooling, as well as stand-by power required is less than 1 watt. Power Supply with TEA driver is equipped with a variety of surge protector that has a high reliability - not easily damaged if any part of a damaged power supply circuit and power transistor or FET heat is not easily damaged. Power supply circuits are dapatapat working on ac input voltage between 85 up to 275v. The way it works with the driver circuit power supply TEA 1507 is quite simple, so easy tracking of damage to the circuit. The picture above is the basic power supply circuit with TEA1507

BAJA Tube Driver BK Tube Driver Repro

The 'BAJA' Tube driver is basically a replica / reverse engineered BK Butler Tube Driver pedal. I absolutely LOVE the BK Butler tube driver, it was and still is a staple in many famous guitar players' distortion tone. Most notably, David Gilmour of Pink Floyd. This build is not simple, or easy so keep that in mind before tackling this one!

High Efficiency White LED Driver Using with NCP5680

This white LED Driver circuit project is based on the NCP5680 high efficiency white LED Driver ic. NCP5680 supports double power flash LED and torch operation . The built-in DC/DC converter is based on a high efficient charge pump structure with 1X, 1.5X and 2X operating modes. The NCP5680 controller is designed to properly drives large external NMOS device with accurate control of the peak current flowing into the LED. Also, the NCP5680 chip includes Open Load and Overload Detection circuit to protect the system against faults at Vout or LED level. High Efficiency White LED Driver Circuit diagram Main features of the NCP5680 are : 2.7 to 5.5 V Input Voltage Range , Dual Power Flash LED Capability , Integrated Overload Protection , Selectable Flash/Torch Mode of Operation , Programmable SuperCAP Re−cycling Current , Capable to Share the DC Voltage to Supply Peripheral Circuits , Indicator LED Function , Integrated Photo Sense Function , Support Camera Strobe , Built−in Short Circuit Pr...

Simple Video Line Driver Circuit Diagram

This is a Simple Video Line Driver Circuit Diagram.This circuit is a video line driver specifically intended for use with a single-ended power supply. As a matter of fact, the synchronised outputs of a line driver for composite-video signals go negative with respect to ground. In order to be able to process these negative signals in a circuit powered from a single-ended supply, it is necessary to AC-couple the input of the opamp as well as level-shift the signal in the positive direction. Circuit diagram : Video Line Driver Circuit Diagram The input is terminated into a 75 Ω resistor (R1). From here, the signal passes through AC-coupling capacitor C2 and is applied to potential divider R2-R3, which provides the necessary DC-offset. The shift into the positive direction amounts to +1.7 V, with the values shown in the schematic. To avoid any misunderstandings we should add that this value is fairly critical. Deviating from the values shown can lead to distortion in the complementary inp...

LED Driver using LNK454DG

A very simple high efficiency led driver circuit can be designed using LNK454DG controller designed by Power Integrations . This LNK454DG led driver is configured as non-isolated discontinuous flyback converter designed to drive LED strings at voltages of 2.5 V to 3.5 V with an output current of 366 mA The circuit meets both line surge and EMI requirements and the low component count allows board dimensions required for LED candelabra bulb replacement applications. LNK454DG led driver is very easy to be configured and require few external electronic parts. LED Driver Schematic Two differential pi (Ï€) filter EMI stages are used with C1, R1, L1 and C2 forming one stage and C2, L2, R2 and C3 the second.The incoming AC is rectified by BR1 and filtered by C1, C2 and C3. The total effective input capacitance, the sum of C1, C2 and C3, was selected to assure correct zero crossing detection of the AC input by the Switch-PL device and to meet high power factor and low THD. Due to the limited in...

Using the TLP250 Isolated MOSFET Driver Explanation and Example Circuits

I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well...

PWMMotor Driver

As the title "PWM DC Motor Driver with Forward / Reverse and Breaking" this series is a PWM DC motor controller that can control DC motors with clockwise rotation and counter-clockwise and is equipped with a braking system.  In a series DC motor control PWM DC Motor Driver with Forward / Reverse and Breaking use this system for SASL PWM DC motor rotation speed. Power driver in a series DC motor PWM DC Motor Driver with Forward / Reverse and Breaking uses mosfet IRF150. Then, to control the direction of rotation of DC motor in the circuit of PWM DC Motor Driver with Forward / Reverse and Breaking uses relays. Then the braking system on a series of PWM DC Motor Driver with Forward / Reverse and Breaking is done by a resistor that is connected to the motor using relays. Fig circuit PWM DC Motor Driver with Forward / Reverse and Breaking Click to view larger See image details a series of PWM DC Motor Driver with Forward / Reverse and Breaking above. DC motor speed is set to pulse...

Power supply with driver TEA1507

Power supply with driver TEA1507 is mostly used by TV branded PHILIPS. Power Supply has an efficiency rate of up to 90% - thus requiring less cooling, as well as stand-by power required is less than 1 watt. Power Supply with TEA driver is equipped with a variety of surge protector that has a high reliability - not easily damaged if any part of a damaged power supply circuit and power transistor or FET heat is not easily damaged. Power supply circuits are dapatapat working on ac input voltage between 85 up to 275v. The way it works with the driver circuit power supply TEA 1507 is quite simple, so easy tracking of damage to the circuit. The picture above is the basic power supply circuit with TEA1507

DIY Dual Stepper Motor Driver Shield for Arduino

Stepper motors are brushless DC motors which can move in discrete steps thanks to the special coil arrangement inside. They are very popular in DIY and industry projects which require accurate mechanical movement control. In this SoloPCB project, we are building a dual stepper motor driver shield based on two Allegro A4988 ICs which can supply up to 35V and 2A and provide overcurrent and thermal protection. [ ]

Dimmer Brightness LED Driver Circuit Diagram

This is a very simple circuit of a dimmer, ie a controller LED brightness, which is powered from the USB port of a PC and a connection is very simple. The resistor R1 sets the maximum current of the LED with the maximum potentiometer, resistor R2 should have a resistance of 10x to 100x greater than R1. The table shows which components to use in accordance with the selected LED. Dimmer-Brightness LED Driver Circuit Diagram