Clap operated Remote Control for Fans

Here is the circuit of clap-operated remote control fans is used to control not only switching properties but also control speed of fan. The main advantage of clap operated remote control for fan is, it can control up to ten-step speeds of fan where normally a fan has three to five step speeds.

Circuit description clap operated remote control for fan

This entire circuit clap operated remote control for fan is divided into four major section i.e. sound-operated trigger pulse generator, clock pulse generator, clock pulse counter and load operator.
Sound-operated trigger pulse: – The heart of this section is transistor T₁ BC148, configured as class-C amplifier mode. The MIC₁ is used to change voice signal into its corresponding electrical signal and is given to base of transistor T₁ in order to amplify and increase its intensity.
Clock pulse generator:- This section is build around timer IC NE555 and configured as monostable multivibrator. The trigger pulse generated by transistor T₁ is given to pin 2 of IC₁ and time period (T) for output high is calculated by formula.

T = 1.1RC

Clock Pulse counter:- This section is build around decade counter CD4017BC which counts the clock pulse generated by timer IC (IC₁). The output from IC₁ is given to pin 14 of IC₂. IC₂ has ten outputs, viz, o, 1, 2, 3, 4…..9. Here we use only three outputs i.e. output 1, 2 and 3 from pin 2, 4, and 7 respectively. Output 4 from pin 10 is directly connected to reset pin 15.
Load operator:- This section is build around three transistor as relay driver to operate three separate relay. Output from each pin of IC₂ is given to base of each transistor through 100Ω and LED as shown in circuit diagram. Output is taken from collector of transistor and is connected to relay. The three LEDs used to indicate gear or speed i.e. LED₁, LED₂ & LED₃ indicates gear 1, gear 2 & gear 3 respectively.
Clap switch

NOTE:-This circuit used to operate in 1^st speed similarly, 2^nd clap for 2^nd speed, 3^rd clap for 3^rd speed and 4^th clap to switch off the fan.

PARTS LIST

Resistors (all ¼-watt, ± 5% Carbon)

R₁ = 10 KΩ

R₂ = 1.2 MΩ

R₃ = 2.2 KΩ

R₄ = 150 KΩ

R₅ = 220 KΩ

R₆ = 10 KΩ

R₇, R₈, R₉ = 100 Ω

Capacitors

C₁, C₂ = 0.1 µF/16V

C₃ = 4.7 µF/16V

C₄ = 0.01 µF (ceramic disc)

C₅ = 1000 µF/12V

Semiconductors

IC₁ = NE555 (Timer IC)

IC₂ = CD4017BE (decade counter)

T₁ = BC148

T₂, T₃, T₄ = BEL187

D₁, D₂ = 1N4001 silicon diode

Miscellaneous

MIC₁ = Condenser microphone 34LOD

LED₁ = Green

LED₂ = yellow

LED₃ = RED

6V-0V-6V, 500mA secondary transformer

OP AMP INTEGRATOR CALCULATOR

Enter the Input Voltage,Vin: Volts Enter the Frequency, f: Hertz Enter the Input Resistance, Rin: Ohms Enter the Value of Capacitor, C: Farads Output Voltage, Vout: Volts OP AMP based Integrator Tutorial and Design

Block diagram of AM transmitter and receiver with explanation

Block diagram of AM transmitter and receiver with explanation AM Transmitter : Transmitters that transmit AM signals are known as AM transmitters. These transmitters are used in medium wave (MW) and short wave (SW) frequency bands for AM broadcast. The MW band has frequencies between 550 KHz and 1650 KHz, and the SW band has frequencies ranging from 3 MHz to 30 MHz. The two types of AM transmitters that are used based on their transmitting powers are: · High Level · Low Level High level transmitters use high level modulation, and low level transmitters use low level modulation. The choice between the two modulation schemes depends on the transmitting power of the AM transmitter. In broadcast transmitters, where the transmitting power may be of the order of kilowatts, high level modulation is employed. In low power transmitters, where only a few watts of transmitting power are required , low...

Using the TLP250 Isolated MOSFET Driver Explanation and Example Circuits

I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well...

Do More

Search This Blog