Skip to main content

Capacitor Motor


Single phase capacitor motors are widely used in household appliances such as water pump , washing machine, freezer, air conditioning . Simple construction with small resources and working with electricity supply voltage 220 V, therefore making the capacitor motor is widely used in household appliances.




Stator winding consists of the main winding terminals U1-U2 notation, with the notation and auxiliary winding terminals Z1-Z2-mesh nets connected to the terminals L1 and U1, and the neutral wire connected to the terminal N U2. Capacitors work function to the main winding phase angle difference with the auxiliary winding approaching 90 °.
Setting the direction of motor rotation can be done with a capacitor (see figure):
• To produce rotation to the left (counterclockwise) working capacitor CB connected to the terminals U1 Z1 and Z2 and the terminal is coupled with the terminal.
• Round to the right (clockwise) a capacitor connected to the terminal
work Z1 and Z2 terminals U1 and U1 is coupled with the terminal.





Capacitor motors with power above 1 kW is equipped with two capacitors and one centrifugal switch. U1-U2 primary winding is connected with the netting L1 and Neutral N. Z1-Z2 auxiliary winding connected in series with the capacitor CB job, and a starting capacitor CA serial with contacts normally close (NC) of the centrifugal switch, see figure .

Initially the main winding, and auxiliary winding voltage gain from t
he netting L1 and Neutral. Then two capacitors CB and CA, both of which form a closed loop so that the rotor began to spin, and when the rotation approaches 70% nominal speed, the centrifugal switch contacts will open and close normally decided auxiliary capacitor CA.




The function of the two capacitors are connected parallel, CA + CB, was to increase the initial torque value to lift the load. After reaching 70% of motor rotation, the centrifugal switch is disconnected so that only the working capacitor CB are still working. If the two capacitors is damaged then the motor torque will decrease drastically, see figure





Examples of the use of motor capacitor is on the electric water pump and compressor.



Comments

Popular posts from this blog

OP AMP INTEGRATOR CALCULATOR

Enter the Input Voltage,Vin: Volts Enter the Frequency, f: Hertz Enter the Input Resistance, Rin: Ohms Enter the Value of Capacitor, C: Farads Output Voltage, Vout: Volts OP AMP based Integrator Tutorial and Design

Using the TLP250 Isolated MOSFET Driver Explanation and Example Circuits

I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well...

Audio signal processing IC for 1 5 V headphone stereo

General Description: The AN7500FHQ is a single chip IC optimum for a 1.5 V headphone stereo system including pre-amp., power amp. and Dolby B type noise reduction circuit. Current consumption in a Dolby circuit off mode has been drastically reduced and an operating supply voltage has also been lowered to 0.98 V. Much fewer external components  have been realized due to an integration of audio signal processing system into a single chip circuitry in a small outline package and space saving mounting of a set. Circuit Diagram Audio signal processing IC for 1.5 V headphone stereo