Sound Operated Music Bell

Sometimes ringing the bell manually becomes difficult, especially when you are holding something in your hands. The sound-operated music bell takes care of the problem .In this circuit, the use of an external relay has been eliminated. The circuit comprises a trigger stage (around BC548B), a timer stage (NE555) and a melody stage (around UM66 and SL100).
Transistor BC548B is biased inn class C operation. Every second sound cause triggering at pin 2 of 555 timer IC.

When VR1 is at maximum, the hold-on time of NE555 is around 30 seconds. But this time period can be set to a lower value by VR1, as per requirement, using the relationship.

T = 1.1*VR1*C1

Where VR1 is the actual resistance of the preset in circuit. UM66 IC has ROM memory of 64 notes which are produced one by one and then over with a sound of a clap, the timer is triggered and the output at pin 3 of IC NE555 goes high which gets applied through diode 1N4001 to pin 2 of musical IC UM66. S UM66 gets the positive supply, it starts giving electrical fluctuations of the music to the base of SL100, and the charming music comes and fed to 4-ohm speaker.

PARTS LIST

Resistors (all ¼-watt, ± 5% Carbon)

R1 = 10 KΩ

R2 = 470 KΩ

R3 = 2.2 KΩ

R4 = 150 KΩ

R5 = 100 Ω

VR1 = 1 MΩ

Capacitors

C1 = 22 µF/16V

C2 = 0.1 µF

C3 = 0.22 µF

C4 = 220 µF/10V

C5 = 0.01 µF

Semiconductors

IC1 = NE555

IC2 = UM66

T1 = BC548B

T2 = SL100

D1 = 1N4001

Miscellaneous

MIC1 = Condensers microphone 34 LOD

SW1 = On/Off switch

Comments

OP AMP INTEGRATOR CALCULATOR

Enter the Input Voltage,Vin: Volts Enter the Frequency, f: Hertz Enter the Input Resistance, Rin: Ohms Enter the Value of Capacitor, C: Farads Output Voltage, Vout: Volts OP AMP based Integrator Tutorial and Design

Block diagram of AM transmitter and receiver with explanation

Block diagram of AM transmitter and receiver with explanation AM Transmitter : Transmitters that transmit AM signals are known as AM transmitters. These transmitters are used in medium wave (MW) and short wave (SW) frequency bands for AM broadcast. The MW band has frequencies between 550 KHz and 1650 KHz, and the SW band has frequencies ranging from 3 MHz to 30 MHz. The two types of AM transmitters that are used based on their transmitting powers are: · High Level · Low Level High level transmitters use high level modulation, and low level transmitters use low level modulation. The choice between the two modulation schemes depends on the transmitting power of the AM transmitter. In broadcast transmitters, where the transmitting power may be of the order of kilowatts, high level modulation is employed. In low power transmitters, where only a few watts of transmitting power are required , low...

Using the TLP250 Isolated MOSFET Driver Explanation and Example Circuits

I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well...

Do More

Search This Blog