Simple Relay Actuating Circuit with Millivolt Sensitivity

Common electromagnetic relays with coil voltage of 5V, 6V or 12V can operate power circuits in the range of 250 to 300 volts and up to 20A. The actuating current of these relays is in the range of 50 to 100 mA. In many applications, such as temperature-controlled equipment, energisation/de-energisation of 5V, 6V or 12V relays for ‘on’/‘off’ control of the load is to be achieved by a few millivolts.

Circuit diagram :

Simple Relay Actuating Circuit Diagram

Here is a simple relay actuating circuit that can be used to energise relays with a few millivolts as the input. As shown in the figure, the circuit is built around op-amp µA741(IC1) followed by an emitter follower using transistor 2N3440 (T1) and a few discrete components. You can change the sensitivity required (when the input is in millivolts range) to energise the relay by changing the value of resistors R1, R2 and R3. In all the cases, values of R4, R5 and R6 remain unchanged.

Resistor R8 is basically a current-limiting resistor used in series with the relay coil. This resistor is not required with a 12V, 200-ohm relay. This circuit can be used to drive 24V relays, by changing the supply voltage to ±18V. To get the best results, using preset VR1 adjust the offset at pin 4 of the op-amp to as low a value as possible. The working of the circuit is simple. When a few millivolts (say, 200 mV) are applied at the input terminal shown in the diagram, the output of IC1 at pin 6 goes high and transistor T1 conducts to energise relay RL1. As a result, the load gets power supply through normally-open (N/O) contacts of the relay.

Assemble the circuit on a general-purpose PCB and enclose in a suitable cabinet. Connect the relay carefully so that the contact can handle the load current.

Do not use resistor R8 with 9V or 12V relays. In this case, connect the junction of the anode of D2 and the coil of the relay to ground.

Author : DR G.N. Acharya - Copyright : EFY

Comments

OP AMP INTEGRATOR CALCULATOR

Enter the Input Voltage,Vin: Volts Enter the Frequency, f: Hertz Enter the Input Resistance, Rin: Ohms Enter the Value of Capacitor, C: Farads Output Voltage, Vout: Volts OP AMP based Integrator Tutorial and Design

Using the TLP250 Isolated MOSFET Driver Explanation and Example Circuits

I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well...

Block diagram of AM transmitter and receiver with explanation

Block diagram of AM transmitter and receiver with explanation AM Transmitter : Transmitters that transmit AM signals are known as AM transmitters. These transmitters are used in medium wave (MW) and short wave (SW) frequency bands for AM broadcast. The MW band has frequencies between 550 KHz and 1650 KHz, and the SW band has frequencies ranging from 3 MHz to 30 MHz. The two types of AM transmitters that are used based on their transmitting powers are: · High Level · Low Level High level transmitters use high level modulation, and low level transmitters use low level modulation. The choice between the two modulation schemes depends on the transmitting power of the AM transmitter. In broadcast transmitters, where the transmitting power may be of the order of kilowatts, high level modulation is employed. In low power transmitters, where only a few watts of transmitting power are required , low...

Do More

Search This Blog