Skip to main content

Simple Over Under Voltage Protection Of Electrical Appliances


This is a simple Over - Under-Voltage Protection Of Electrical Appliances. This circuit protects refrigerators as well as other appliances from over and under-voltage. Operational amplifier IC LM324 (IC2) is used here as a comparator. IC LM324 consists of four operational amplifiers, of which only two operational amplifiers (N1 and N2) are used in the circuit.

Over - Under-Voltage Protection Of Electrical Appliances Circuit Diagram


Over - Under-Voltage Protection Of Electrical Appliances


The unregulated power supply is connected to the series combination of resistors R1 and R2 and potmeter VR1. The same supply is also connected to a 6.8V zener diode (ZD1) through resistor R3.Preset VR1 is adjusted such that for the normal supply of 180V to 240V, the voltage at the non-inverting terminal (pin 3) of operational amplifier N1 is less than 6.8V. Hence the output of the operational amplifier is zero and transistor T1 remains off. The relay, which is connected to the collector of transistor T1, also remains de energised. As the AC supply to the electrical appliances is given through the normally closed (N/C) terminal of the relay, the supply is not disconnected during normal operation.

When the AC voltage increases beyond  240V, the voltage at the non-inverting terminal (pin 3) of operational amplifier N1 increases. The voltage at the inverting terminal is still 6.8V because of the zener diode. Thus now if the voltage at pin 3 of the operational amplifier is higher than 6.8V, the output of the operational amplifier goes high to drive transistor T1 and hence energise relay RL. Consequently, the AC supply is disconnected and electrical appliances turn off. Thus the appliances are protected against over-voltage. Thus the appliances are protected against over-voltage.

Now let’s consider the under-voltage condition. When the line voltage is below 180V, the voltage at the inverting terminal (pin 6) of operational amplifier N2 is less than the voltage at the non-inverting terminal (6V). Thus the output of operational amplifier N2 goes high and it energises the relay through transistor T1. The AC supply is disconnected and electrical appliances turn off. Thus the appliances are protected against under-voltage. IC1 is wired for a regulated 12V supply.

Thus the relay energises in two conditions: first, if the voltage at pin 3 of IC2 is above 6.8V, and second, if the voltage at pin 6 of IC2 is below 6V. Over-voltage and under-voltage levels can be adjusted using presets VR1 and VR2, respectively.

Sourced by : EFY Author :  C.H. VITHALANI

Labels:

Comments

Post a Comment

Popular posts from this blog

OP AMP INTEGRATOR CALCULATOR

Enter the Input Voltage,Vin: Volts Enter the Frequency, f: Hertz Enter the Input Resistance, Rin: Ohms Enter the Value of Capacitor, C: Farads Output Voltage, Vout: Volts OP AMP based Integrator Tutorial and Design
Post a Comment
Read more

Block diagram of AM transmitter and receiver with explanation

Block diagram of AM transmitter and receiver with explanation AM Transmitter : Transmitters that transmit AM signals are known as AM transmitters. These transmitters are used in medium wave (MW) and short wave (SW) frequency bands for AM broadcast. The MW band has frequencies between 550 KHz and 1650 KHz, and the SW band has frequencies ranging from 3 MHz to 30 MHz. The two types of AM transmitters that are used based on their transmitting powers are: ·          High Level ·          Low Level High level transmitters use high level modulation, and low level transmitters use low level modulation. The choice between the two modulation schemes depends on the transmitting power of the AM transmitter. In broadcast transmitters, where the transmitting power may be of the order of kilowatts, high level modulation is employed. In low power transmitters, where only a few watts of transmitting power are required , low...
Post a Comment
Read more

Using the TLP250 Isolated MOSFET Driver Explanation and Example Circuits

I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well...
Post a Comment
Read more