Zener Tester Circuit Diagram

The circuit can be simply Q1 is connected as a current source. By D1, there is a constant voltage on the base, and it is worth considering the selected resistor in the emitter approximately 5.6 V. With an emitter resistor of 5K6 R2 will then 1mA through the transistor.

With the chosen resistors in the circuit the current is approximately: 1mA, 2mA, 5mA, 10mA and 20mA. Great precision is not required.

If meter is chosen here for a small DVM module. However, every other meter is applicable, provided that the input resistance is high enough.

Construction:
The circuit is simple to build on a piece of PCB holes. Note that the DVM module separate from the circuit galvanic isolated power supply needs.

Using
Connect the test zener diode between the terminal A and K. Start with a current of 2mA. This is a safe value for most type zener diodes. Depending on the type of zener diode, may be chosen for a greater current. Than the Zener voltage will vary slightly.

Join the zener diode on backwards, the meter will indicate approximately 0.7V. The same picture shows an ordinary silicon diode. A germanium diode, a voltage of about 0.3 V to 0.4 V indicate when a Schottky approximately 0.2 V indicates.

Connect an LED to A and K, it will be highlighted and the Vforward (LED voltage) of the LED indicate.
The diode / LED failure, the meter displays zero if the voltage at the collector of Q1 is, this is> 25V.

Zener Tester Circuit Diagram

parts List

     Bridge rectifier BR1 = 40V 500mA
     R1 = 3k3 ¼ W
     R2 = 5K6 ¼ W
     R3 = 2k7 ¼ W
     R4 = 1k ¼ W
     R5 = 560 ohm W ½
     R6 = 270 ohm ½ W
     C1 = 470µF 35V
     D1 = 6V2 zener 400mW
     Q1 = BC161-16
     S1 = on / off switch
     S2 = 5 modes 1 mom ignition switch
     ENG = The diode under test (Device Under Test)
     DVM DVM = module of BACO or Dick Best (input adapted to 200V)

Comments

OP AMP INTEGRATOR CALCULATOR

Enter the Input Voltage,Vin: Volts Enter the Frequency, f: Hertz Enter the Input Resistance, Rin: Ohms Enter the Value of Capacitor, C: Farads Output Voltage, Vout: Volts OP AMP based Integrator Tutorial and Design

Block diagram of AM transmitter and receiver with explanation

Block diagram of AM transmitter and receiver with explanation AM Transmitter : Transmitters that transmit AM signals are known as AM transmitters. These transmitters are used in medium wave (MW) and short wave (SW) frequency bands for AM broadcast. The MW band has frequencies between 550 KHz and 1650 KHz, and the SW band has frequencies ranging from 3 MHz to 30 MHz. The two types of AM transmitters that are used based on their transmitting powers are: · High Level · Low Level High level transmitters use high level modulation, and low level transmitters use low level modulation. The choice between the two modulation schemes depends on the transmitting power of the AM transmitter. In broadcast transmitters, where the transmitting power may be of the order of kilowatts, high level modulation is employed. In low power transmitters, where only a few watts of transmitting power are required , low...

Using the TLP250 Isolated MOSFET Driver Explanation and Example Circuits

I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well...

Do More

Search This Blog