LASER BURGLAR ALARM CIRCUIT

SIMPLE LASER BURGLAR ALARM CIRCUIT

It is an advanced, simple, efficient and low cost circuit. You can use this circuit on Home, office, locker or anywhere for Security purpose.

As the name suggests, the circuit is based on Laser. We all know about the features of Laser, Long Range, pointed beam, Low power consumption and so on.

The Transmitter section of this circuit is a LASER.

Circuit Diagram of Laser Burglar Alarm

Components Used In Laser Burglar alarm circuit

IC TLO71

T1 L14F1 (Photo Transistor)

T2 BC 548

R1 1KΩ

R2 4.7KΩ

R3 4.7KΩ

R4 100Ω

C1 470μF

C2 1000μF

LED

Buzzer

9V Battery

Working of Laser Intruder/Burglar Alarm Circuit.

This circuit alarms whenever someone cross the Laser beam transmitted from a LASER. The output of IC TL071 goes high whenever their is no Light(Laser) Ray. This output voltage is further amplified by means of a NPN transistor Q2, which will drive the buzzer and generates an alarm.

How to Setup Laser Burglar Alarm?

As i mentioned above, you can use an ordinary Laser as Transmitter and the circuit shown in the figure act as Receiver. The sensing or receivng part of this circuit consisting of a PhotoTransistor L14F1. It will detect Laser Beam and the output is given to IC TL071. Whenever an intruder cross or cuts the ray the circuit alarms.

ADVANTAGES OF THIS CIRCUIT COMPARED TO OTHER SECURITY CIRCUITS

The circuit is quite simple to Do. (You can try this circuit for your project also)

Lasers Having Long range, so we can cover a long area to prevent the access of Intruders or robbers

Low cost

Good Efficiency

Commonly Available Components

Laser Diode working Principle

Comments

OP AMP INTEGRATOR CALCULATOR

Enter the Input Voltage,Vin: Volts Enter the Frequency, f: Hertz Enter the Input Resistance, Rin: Ohms Enter the Value of Capacitor, C: Farads Output Voltage, Vout: Volts OP AMP based Integrator Tutorial and Design

Using the TLP250 Isolated MOSFET Driver Explanation and Example Circuits

I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well...

Block diagram of AM transmitter and receiver with explanation

Block diagram of AM transmitter and receiver with explanation AM Transmitter : Transmitters that transmit AM signals are known as AM transmitters. These transmitters are used in medium wave (MW) and short wave (SW) frequency bands for AM broadcast. The MW band has frequencies between 550 KHz and 1650 KHz, and the SW band has frequencies ranging from 3 MHz to 30 MHz. The two types of AM transmitters that are used based on their transmitting powers are: · High Level · Low Level High level transmitters use high level modulation, and low level transmitters use low level modulation. The choice between the two modulation schemes depends on the transmitting power of the AM transmitter. In broadcast transmitters, where the transmitting power may be of the order of kilowatts, high level modulation is employed. In low power transmitters, where only a few watts of transmitting power are required , low...

Do More

Search This Blog